The machine does one thing the hand and the hips can't: it holds a pace and never tires of it. Set it, and it keeps going exactly as fast and as deep as you told it to — hands-free, both of yours free for whatever else. The first session is the only one that feels like homework. Here's how to skip the fumbling.
anchor it first
Almost every problem with a machine traces back to one thing: it moved. A machine that creeps, taps, or walks across the floor mid-session kills the rhythm and adds a rattle you'll hear through the wall.
So before anything else, lock it down.
- Suction base? Press it onto a hard, smooth, clean surface — sealed floor, tile, a board. Not carpet, not a soft rug; suction needs something flat to grip. Push the lever, give it a tug to confirm it's set.
- Clamp or weighted base? Clamp to a solid bed frame or table edge, or load the weight per the instructions.
- Then test it dry. Run it at low speed for ten seconds with nothing attached and watch it. If it shifts, re-anchor before you go further.
A machine that stays put does half the work of a good session on its own.
set the angle and the height
The shaft angle decides everything about how it feels. Most machines pivot — loosen the joint, set the angle, lock it.
- Flat / low angle mirrors lying on your back or on your stomach.
- Steeper / upward angle suits kneeling or being on top of it.
- Match the height to where you'll be — floor, bed, or chair. You want to meet it without straining to reach.
Set this with the machine off and your body roughly in position, so you're not adjusting mid-session.
find your pace
This is where people overshoot. The instinct is to crank it. Don't — not at first.
- Start slow. Lowest speed, short strokes. Let your body meet the rhythm before you add to it.
- Add stroke length before speed. A longer, slower stroke usually feels better than a short fast one. Open the stroke up first, then bring the speed up if you want it.
- Climb gradually. Speed is a dial, not a switch. The machine doesn't get tired, so there's no rush — you set the pace and it holds it.
- Keep the control in reach. Whatever you're doing, you should be able to back it off in one motion. A wired remote or a dial within arm's reach beats fumbling for a phone app mid-session.
The whole point is that once it's dialed in, you stop managing it and it just runs.
lube, attachments, and what's touching you
- Use more lube than you think. A machine keeps a steady pace and doesn't read the room, so it won't slow down when you've gone dry. Reapply before you need to.
- Match lube to material. Water-based works on everything. Silicone lube lasts longer but degrades silicone and TPE attachments — so water-based is the safe default for most attachments.
- Body-safe attachment. Silicone (non-porous, boilable) for anything internal and regular; TPE is fine but porous — condom it and use water-based lube only. Look for ISO 3533, the international sex-toy safety standard.
If you're unsure which connector your machine takes or whether your own toys will fit, that's its own rabbit hole — we wrote it up in sex machine attachments, explained.
solo or with someone
Solo, the machine is the partner that holds the pace while both your hands stay free. With someone, it's a third thing in the room — one of you can run the dial while the other does everything else, or it takes over so neither of you has to keep the rhythm. There's no single right way; the machine doesn't care, and that's the point.
clean it after
- Pop the attachment off and wash it: warm water and mild soap for everything, boil silicone to actually sanitize it. Let it dry fully before it goes away — porous TPE especially.
- Wipe down the machine body with a damp cloth. Don't soak the motor housing.
- Store the shaft retracted and the whole thing somewhere dry.
Two minutes after, and it's ready for next time instead of being a chore you avoid.
the short version
Anchor it before anything else, set the angle with the machine off, start slow and open the stroke before the speed, use more lube than feels necessary, keep a body-safe attachment on it, and clean it the moment you're done. The first session teaches you the rest.
FRAME 01 is built around the part that trips people up — a suction base that anchors to the floor so it doesn't wander, under 40 dB at a normal pace, and a stroke and torque you set and it holds without flinching. The rest of the thrusting machines are on the page with their real numbers too.
